m35 www.vishay.com vishay revision: 07-nov-11 1 document number: 40095 for technical ques tions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 wet tantalum capacitors surface mount, molded case features ? molded surface mountable design ? terminations: standa rd tin/lead (snpb), 100 % tin (rohs compliant) available ? industry standard ratings ? model m35 wet tantalum electrolytic chip capacitors incorporate th e advantages of all the varieties of electrolytic capacitors and eliminate most of the disadvantages. these unit s have a 3 v reverse voltage capability at + 85 c and a higher ripple current capability than any other electrolytic ty pe with similar combinations of capacitance and case size. ? compliant to rohs directive 2002/95/ec note * pb containing terminations are not rohs compliant, exemptions may apply performance characteristics operating temperature: - 55 c to + 85 c (to + 125 c with voltage derating) capacitance tolerance: at 120 hz, + 25 c. 20 % standard. 10 %, 5 % available as special. dc leakage current (dcl max.): at + 25 c and above: leakage current shall not exceed the values listed in the standard ratings tables. life test: capacitors are capable of withstanding a 2000 h life test at a temperature of + 85 c or + 125 c at the applicable rated dc working voltage. following life test: 1. dcl, measured at + 85 c rated voltage, shall not be in excess of the original requirement. 2. the equivalent series resistance shall not exceed 150 % of the initial requirement. 3. change in capacitance shall not exceed 10 % from the initial measurement. note ? packaging: the use of formed plastic tubes for packing bulk components is standard ordering information m35 c 826 m 125 b z s l model case code capacitance capacitance tolerance dc voltage rating at + 85 c termination and packaging reliability level temp esr see ratings and case codes table this is expressed in picofarads. the first two digits are the significant figures. the third is the number of zeros to follow. k = 10 % m = 20 % this is expressed in volts. to complete the three-digit block, zeros precede the voltage rating. a decimal point is indicated by an r (6r3 = 6.3 v) a = 100 % tin (rohs compliant), bulk b = std, tin/lead, bulk z = non-er s = std s = std. l = low dimensions in inches [millimeters] case code l (max.) w h p (min.) t w t h (min.) c 0.835 [21.2] 0.315 0.012 [8 0.3] 0.295 0.012 [7.5 0.3] 0.118 [3.0] 0.236 0.012 [6.0 0.3] 0.075 [1.9] t h h t w l wp
m35 www.vishay.com vishay revision: 07-nov-11 2 document number: 40095 for technical ques tions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 mounting due to the size and weight of these capacitors, we recommend that a supplemental mounting rest raint to be used in printed circuit board attachment in addi tion to the reflowed solder. one recommendation is to use an adhesive such as defined in the j-std-001ds. this is the space application electronic hardware addendum to j-std-001 (requireme nts for solder electrical and electronic assemblies). recommended reflow profiles t p lead (pb)-free t p sn/pb t p t l lead (pb)-free t l sn/pb t s min. lead (pb)-free t s min. sn/pb t s max. lead (pb)-free t s max. sn/pb t s lead (pb)-free t s sn/pb t l 260 c 240 c 10 217 c 183 c 150 c 100 c 200 c 150 c 60 to 150 60 to 90 60 standard ratings capacitance (f) case code part number max. esr at + 25 c max. esr at - 55 c max. dcl (a) at max. capacitance change (%) at max. ripple 40 khz rms (ma) + 25 c + 85 c + 125 c - 55 c + 85 c + 125 c 6 v dc at + 85 c; 4 v dc at + 125 c 30 c m35c306(1)006(2)zs(3) 4.0 100 1.0 2.0 - 40 + 10.5 + 12 820 68 c m35c686(1)006(2)zs(3) 3.2 60 1.0 2.0 - 40 + 14 + 16 960 220 c m35c227(1)006(2)zs(3) 3.0 36 2.0 9.0 - 64 + 13 + 16 1000 8 v dc at + 85 c; 5 v dc at + 125 c 25 c m35c256(1)008(2)zs(3) 4.0 100 1.0 2.0 - 40 + 10.5 + 12 820 56 c m35c566(1)008(2)zs(3) 3.3 59 1.0 2.0 - 40 + 14 + 16 900 180 c m35c187(1)008(2)zs(3) 3.0 45 2.0 9.0 - 60 + 13 + 16 1000 10 v dc at + 85 c; 7 v dc at + 125 c 20 c m35c206(1)010(2)zs(3) 4.0 120 1.0 2.0 - 32 + 10.5 + 12 820 47 c m35c476(1)010(2)zs(3) 3.7 90 1.0 2.0 - 36 + 14 + 16 855 120 c m35c127(1)010(2)zs(3) 3.2 54 2.0 6.0 - 40 + 14 + 16 900 150 c m35c157(1)010(2)zs(3) 3.0 54 2.0 9.0 - 55 + 13 + 16 900 note ? part number definitions: (1) capacitance to lerance: k, m (2) termination/packaging: (see ordering information) reliability level: z = non-er temperature: s = std (3) esr: s = std, l = low (1/2 standard esr value) temperature (c) 25 c time (s) all case codes t p c t l c t s max. c t s min. c t p (t l ) preheat (t s )
m35 www.vishay.com vishay revision: 07-nov-11 3 document number: 40095 for technical ques tions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 15 v dc at + 85 c; 10 v dc at + 125 c 15 c m35c156(1)015(2)zs(3) 4.4 155 1.0 2.0 - 24 + 10.5 + 12 780 33 c m35c336(1)015(2)zs(3) 4.0 90 1.0 2.0 - 28 + 14 + 16 820 82 c m35c826(1)015(2)zs(3) 3.9 72 2.0 6.0 - 35 + 12 + 16 900 100 c m35c107(1)015(2)zs(3) 3.9 72 2.0 9.0 - 44 + 13 + 16 900 25 v dc at + 85 c; 15 v dc at + 125 c 10 c m35c106(1)025(2)zs(3) 5.3 220 1.0 2.0 - 16 + 8 + 9 715 22 c m35c226(1)025(2)zs(3) 4.2 140 1.0 2.0 - 20 + 10.5 + 12 800 56 c m35c566(1)025(2)zs(5) 4.3 90 2.0 6.0 - 25 + 12 + 15 850 68 c m35c686(1)025(2)zs(5) 4.3 90 2.0 9.0 - 40 + 12 + 15 850 30 v dc at + 85 c; 20 v dc at + 125 c 8 c m35c805(1)030(2)zs(3) 6.6 275 1.0 2.0 - 16 + 8 + 12 640 15 c m35c156(1)030(2)zs(3) 6.2 175 1.0 2.0 - 20 + 10.5 + 12 780 47 c m35c476(1)030(2)zs(3) 5.2 100 2.0 6.0 - 23 + 12 + 15 800 56 c m35c566(1)030(2)zs(3) 5.2 100 2.0 9.0 - 38 + 12 + 15 800 35 v dc at + 85 c; 22 v dc at + 125 c 15 c m35c156(1)035(2)zs(3) 6.2 175 0.75 1.5 - 20 + 10.5 + 12 660 39 c m35c396(1)035(2)zs(3) 4.1 61 2.0 6.0 - 22 + 12 + 14 820 50 v dc at + 85 c; 30 v dc at + 125 c 5 c m35c505(1)050(2)zs(3) 8.0 400 1.0 2.0 - 16 + 5 + 6 580 10 c m35c106(1)050(2)zs(3) 6.4 250 1.0 2.0 - 24 + 8 + 9 715 33 c m35c336(1)050(2)zs(3) 5.0 135 2.0 9.0 - 29 + 10 + 12 700 60 v dc at + 85 c; 40 v dc at + 125 c 4 c m35c405(1)060(2)zs(3) 9.3 550 1.0 2.0 - 16 + 5 + 6 525 8.2 c m35c825(1)060(2)zs(3) 6.6 275 1.0 2.0 - 24 + 8 + 9 625 27 c m35c276(1)060(2)zs(3) 5.0 144 3.0 12 - 24 + 10 + 12 700 75 v dc at + 85 c; 50 v dc at + 125 c 3.5 c m35c355(1)075(2)zs(3) 9.5 650 1.0 2.0 - 16 + 5 + 6 525 6.8 c m35c685(1)075(2)zs(3) 6.8 300 1.0 2.0 - 20 + 8 + 9 610 22 c m35c226(1)075(2)zs(3) 5.1 157 3.0 12 - 19 + 10 + 12 600 100 v dc at + 85 c; 65 v dc at + 125 c 2.5 c m35c255(1)100(2)zs(3) 10.6 950 1.0 2.0 - 16 + 7 + 8 505 4.7 c m35c475(1)100(2)zs(3) 8.5 500 1.0 2.0 - 16 + 7 + 8 565 10 c m35c106(1)100(2)zs(3) 5.9 200 3.0 12 - 17 + 10 + 12 800 125 v dc at + 85 c; 85 v dc at + 125 c 1.7 c m35c175(1)125(2)zs(3) 15.6 1250 1.0 2.0 - 16 + 7 + 8 415 3.6 c m35c365(1)125(2)zs(3) 10.0 600 1.0 2.0 - 16 + 7 + 8 520 6.8 c m35c685(1)125(2)zs(3) 11.7 300 3.0 12 - 14 + 10 + 12 700 standard ratings capacitance (f) case code part number max. esr at + 25 c max. esr at - 55 c max. dcl (a) at max. capacitance change (%) at max. ripple 40 khz rms (ma) + 25 c + 85 c + 125 c - 55 c + 85 c + 125 c note ? part number definitions: (1) capacitance to lerance: k, m (2) termination/packaging: (see ordering information) reliability level: z = non-er temperature: s = std (3) esr: s = std, l = low (1/2 standard esr value)
m35 www.vishay.com vishay revision: 07-nov-11 4 document number: 40095 for technical ques tions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 performance characteristics of m35 capacitors electrical characteristics item performance characteristics operating temperature range - 55 c to + 125 c capacitor tolerance 20 %, 10 % at 120 hz capacitance change (maximum) limits per standard rating s table. measured per requ irements of mil-prf-39006. esr ac ripple current dcl (maximum leakage current) impedance (maximum) reverse voltage reverse voltage shall be in accordance with mil-prf-39006/22. units are capable of withstanding 3 v in reverse at + 85 c for 125 h. surge voltage surge voltage shall be in accordance with mil-prf-39006. the dc rated surge voltage is the maximum voltag e to which the capacitors should be subjected under any conditions. this includes transients an d peak ripple at the highest line voltage. the surge voltage is 115 % of rated dc working voltage. life test the capacitors sh all be capable of withstan ding a 2000 h life test at 85 c at rated voltage. environmental characteristics item condition comments hermeticity mil-prf-39006 the internal componen t has been tested to be compliant to the hermeticity requirements of mil-prf-39006/22. the internal component has been tested to be compliant to the moisture resistance requ irements of mil-prf-39006/22. the internal component has been tested to be compliant to the altitude or reduce d barometric pressu re requirements of mil-prf-39006/22 (150 000 feet). moisture resistance mil-prf-39006 altitude/barometric pressure (reduced) mil-prf-39006 mechanical characteristics item condition comments thermal shock mil-std-202, method 107, a per mil-prf-39006, 30 cycles shock mil-std-202, method 213 per mil-prf-39006, 500 g vibration (high frequency) mil-std-202 , method 204 per mil-prf-39006, 80 g vibration (rando m) mil-std-202, method 214 per mil-prf-39006, 53.79 g resistance to solder h eat mil-std-202, method 210 the capacitor must withstand solder dipping of the terminals at 260 c for 10 s. the capacitor must not be visibly damaged and the electrical characteristics must not be affected. solderability ansi j-std-002 the terminations must be solderable per the requirements of mil-prf-55365 para. 4.10 part markings mil-std-1285 the part marking shall include vishay name, trademark, capacitance, voltage, date code and lot symbol. weight (typical) in g 3.5 pad dimensions in millimeters case code a (min.) b (nom.) c (nom.) d (nom.) c 22.7 14.7 4.0 6.4 standard packaging quantity series case code bulk/tube m35 c 10 pcs a cb d c
legal disclaimer notice www.vishay.com vishay revision: 02-oct-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized vishay personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. vishay intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some vishay documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.
|
